Product Descriptions     Economic Benefits    Green Buildings  
 
Product Descriptions

Framing Systems
Roof Panels
Wall Panels
Other Panels
Finishes and Accessories
Glossary

Click On Any of the  Above Links for Further Info.

   

               ROOF PANELS

BS&C Buildings offers four distinct roof systems — SSR, SLR, Panel Rib, and Snap Seal — to meet your particular needs.


SSR

Low slope, low maintenance

The SSR System is a low-slope, clip mounted standing seam roof that meets the most demanding performance specifications. These durable, low-maintenance panels are interlocked and mechanically field-seamed in place, yielding a single membrane allowing for quick construction and strength at a lower cost. The slotted clip allows up to 3 1/4" of thermal movement. SSR's patented ridge system seams together and provides a true expansion joint. Panels are available in either 22 or 24 gauge zinc aluminum coated steel with 3"-high ribs. Available in 6 colors plus base Galvalume.™

  • Economical
  • Field-seamed weather-resistant joint
  • Roof slopes as low as 1/4" in 12"
  • 24" coverage
  • Lengths up to 50'
  • UL 90 Wind Uplift Rating available
  • U.S. Army Corps of Engineers-approved for Wind Uplift Resistance
  • Dade County Building Commission-approved
  • Factory Mutual-approved

 

Downloadable product information for SSR

 

Minimizing heat escape where insulation is compressed over purlins or joists is one of the best ways to improve the thermal efficiency of a building. Better thermal efficiency means lower energy costs and lower life-cycle costs.  BS&C's Thermal Block provides an economical way to improve thermal performance by reducing heat escape at contact areas over roof secondary. When thermal blocks are used along with 6" rolled fiberglass insulation, there is an improvement of 25% compared to systems where thermal blocks are not used. 

 

Downloadable product information on Thermal Block for SSR 

BS&C’s patented SuperBlock system for SSR is capable of delivering an ASTM-C236 Hot Box tested, in-place R-value of 22.8 with a non-reflective facing. If using a reflective facing, the R-value can be as high as 23.5.

Dowloadable product information on SuperBlock for SSR

BS&C offers Tuf-Dome, a curbless domed skylight, or choose a zinc-coated aluminum skylight curb for use with the SSR roof system. 

Downloadable product information on Tuf-Dome for SSR

Downloadable product information on CFR Roof Curb for SSR

BS&C's SSR Seamed Ridge system allows for a consistent look and efficient closure and protection at the apex of the roof.

Downloadable product information for Seamed Ridge



SLR

Meets architectural specifications

This architectural/structural roof system is a low-slope, concealed-fastener roof that meets most architectural performance specifications. Using factory-installed sealant, pre-caulked galvanized clips, and field-seaming, this roof system provides unsurpassed performance and leak resistance. Panels are available in 22 or 24 gauge Galvalume steel. The thermally responsive galvanized panel clip combines a 22 gauge hook and a 16 gauge clip.

  • Economical
  • Field-seamed weather-resistant joint
  • Roof slopes as low as 1/4" in 12"
  • 16" coverage with 2" depth
  • Lengths up to 40'
  • UL 90 Wind Uplift Rating available
  • U.S. Army Corps of Engineers-approved for Wind Uplift Resistance
  • Factory Mutual-approved

 Downloadable product information for SLR


  
Panel Rib Roof

Attractive and economical

This attractive, high-quality, low-maintenance roof is ideal for tight budgets. The 36"-wide panel is attached with self-drilling, stainless steel color-matched fasteners. This system offers you enhanced roof integrity and quicker installation. Sealant is applied to every metal-to-metal contact point, resulting in a weather-resistant roof. The panel has 1-1/4" high ribs and comes in lengths up to 41'. Panels are available in either 24 or 26 gauge zinc aluminum coated steel.

  • Economical;
  • Roof slopes as low as 1/2" in 12"
  • 36" coverage
  • Lengths up to 41'
  • UL 60 and UL 90 Wind Uplift Ratings available
  • Dade County Building Commission-approved

Downloadable Product information for Panel Rib Roof

 


 


Snap Seal

High-performance

The Snap Seal Architectural Roof System is a high-performance, concealed-fastener, standing seam roof system that is both good-looking and durable. It offers a unique snap and seal joinery system for weather–resistance and is available in either 22 or 24 gauge Galvalume steel with 1-3/4"-high ribs and thermally responsive, galvanized 18 gauge panel clips.

  • Economical
  • 18" coverage
  • Lengths up to 41'
  • Fast installation

Downloadable product information for Snap Seal Roof

 

 

 
 
buildingservicesandconstruction Copyright 2009 Terms Of Use Statement
Privacy Statement